Kee_Gate_Handy_Guide_UK

1. • Maximum width 1m, fully adjustable to smaller apertures allows broad fle xibility of use for single and full height gates. 1.8m total opening for double gat es. • R eversible, hinges can be on the left or right hand side of an opening to allo w easy installation • Cy cle tested for 50,000 openings for assured durability • Salt spr ay tested for corrosion resistance (672 hours) to allow continuous operation, e ven in corrosive environments • Compliant with EN 14122 : 2016, OSHA & CSA requirements, CE marked for assured and safe operation A Gate is required... AT HEIGHT BS 4211 requires a Full Height Gate to be mounted at the top of any fixed ladder for the ladder to be compliant. Section 6 of BS 4211:2005 - Permanently Fixed Ladders states - ‘...passage from the ladder to an arrival area, shall be protected by a full height self closing safety gate’ ‘Chains are not an acceptable substitute’ BS 4211:2005 AT GROUND LEVEL Where there are gaps withing railings which lead to a risk area. For example, areas such as factory or warehouse floors, where guardrail protects persons from vehicular traffic, machinery or other hazards. Section 7.4.1 of BS 14122-3:2016 - Safe Access to Machinery states - ‘A self closing gate shall be used to allow passage of persons and shall meet the requirements of the adjacent guardrails’ It is your duty to advise customers of unsafe areas which would benefit from Kee Gates! Why C hoose Kee Gate? T ested - Compliant - Reliable - High Quality - Made in England

2. Galvanised Finish All steel components galvanised to BS EN ISO 1461. All fixings are hot dipped galvanised to BS EN ISO 1461. Powder C oated F inish Polyester Powder Coating to EN 13438. RAL code 1021. Alternative RAL colours can be produced to suit customer requirements. Compliant - BS EN ISO 14122 : 2016 , BS 4211, BS EN 13774 Life Cycle Testing - BS 6375-2:2009 Clause 6.5 - Opening and closing of g ate through 90 degrees. Salt Spray Testing - ASTM B117 - 11 - 55 over 200 hours to assess performance of coating to resist corrosion. Single Gate •Provides safe access for up to 1m wide openings •Compliant with the latest BS EN 14122 standard •Use at height or ground level •Galvanised or powercoated finishes Double Gate •Provides safe access for up to 1.8m wide openings •Compliant with the latest 14122 standard •Use at ground level •Galvanised or powercoated finishes Full Height Gate •Provides safe access for up to 1m wide openings. •Provides full height (1.1mm) protection •Compliant with the latest 14122 standard •Includes aluminium toeboard Which Kee Gate? 1000mm 670 mm BS EN 1 4122 1 3374  Toeboard 50k Cycle Tested  Galv/ PC 1800mm 670 mm BS EN 1 4122 1 3374  50k Cycle Tested  Galv/ PC 1000mm 1100 mm BS EN 1 4122 4211  Galv/ PC 1000mm 670 mm BS EN 1 4122 1 3374  Toeboard 50k Cycle Tested  Galv/ PC 1800mm 670 mm BS EN 1 4122 1 3374  50k Cycle Tested  Galv/ PC 1000mm 1100 mm BS EN 1 4122 4211  Galv/ PC 1000mm 670 mm BS EN 1 4122 1 3374  Toeboard 50k Cycle Tested  Galv/ PC 1800mm 670 mm BS EN 1 4122 1 3374  50k Cycle Tested  Galv/ PC 1000mm 1100 mm BS EN 1 4122 4211  Galv/ PC Need help? Contact Kee Safety n ow! T: 01384 632 188 - E: technicalsupport@keesafety.com www.keesafety.co.uk