TR-800 Datasheet Updates FV for office use

1. 3M ™ Versaflo ™ Powered Air Turbo TR‑800 Product description The 3M ™ Versaflo ™ Powered Air Turbo TR-800 is an ATEX Certified belt - mounted air purifying device that can be used in certain potentially explosive atmospheres. When combined with an approved headtop or facepiece, it forms a power-assisted system for respiratory protection against particles, nuisance odours (where applicable) and gases and vapours. A range of approved breathing tubes are available depending on which headtop or facepiece is selected. Ŕ Approved to Zone 0 requirements so may be suitable for areas where potentially explosive atmospheres are expected and permanent in normal operations (see technical specifications for more information) Ŕ Three user selectable flow rates Ŕ Controlled airflow delivers steady flow as battery discharges or filter loads with particulates Ŕ Display shows battery charge status and particulate loading status during use Ŕ No user calibration of the turbo is required Ŕ Electronic audible and visual alarm in case of low battery and/or low air flow Ŕ Simple, intuitive, easy to use two-button operation Ŕ Six filter options available: Ŕ P Ŕ P plus nuisance level* organic vapours and acid gas which also offers protection against hydrogen fluoride up to 10 x Threshold Limit Value Ŕ A1P Ŕ A1B1E1P Ŕ A2P Ŕ A2B2E2K1HgP Ŕ Lithium ion battery with LED to indicate charge status Ŕ Two belt options: Ŕ Easy-clean belt Ŕ High durability belt Ŕ Suitable for shower decontamination (IP54) when using filter cover and temporary submersion (IP67) when fitted with cleaning plugs Breathing tube options Facepiece Breathing tube 3M ™ Versaflo ™ S-Series Hoods and Headcovers 3M ™ Versaflo ™ M-Series Faceshields and Helmets BT-20S/L, BT-30 or BT-40 3M ™ Full Facepiece Respirators 6000 Series 3M ™ Full Facepiece Respirators 7907S Series 3M ™ Half Facepiece Respirators 7500 Series BT-63 or BT-64 3M ™ Vision ™ Full Facepiece Respirator FM4 3M ™ Promask ™ Full Facepiece Respirator FM3 BT-54 Technical datasheet *Nuisance level refers to concentrations below the Threshold Limit Value

5. 3M ™ Versaflo ™ Powered Air Turbo 3M Ireland Limited The Iveagh Building The Park, Carrickmines Dublin 18 1 800 320 500 Important notice The use of the 3M product described within this document assumes that the user has previous experience of this type of product and that it will be used by a competent professional. Before any use of this product it is recommended to complete some trials to validate≈the performance of the product within its expected application. All information and specification details contained within this document are inherent to this specific 3M product and would not be applied to other products or environment. Any action or usage of this product made in violation of this document is at the risk of the user. Compliance to the information and specification relative to the 3M product contained within this document does not exempt the user from compliance with additional guidelines (safety rules, procedures). Compliance to operational requirements especially in respect to the environment and usage of tools with this product must be observed. The 3M group (which cannot verify or control those elements) would not be held responsible for the consequences of any violation of these rules which remain external to its decision and control. Warranty conditions for 3M products are determined with the sales contract documents and with the mandatory and applicable clause, excluding any other warranty or compensation. Personal Safety Division 3M United Kingdom PLC 3M Centre Cain Road, Bracknell Berkshire RG12 8HT 0870 60 800 60 www.3M.eu/PPEsafety Please recycle. Printed in the UK. 3M, Promask, Versaflo and Vision are trademarks of 3M Company. © 3M 2020. All rights reserved. OMG77310.

4. 3M ™ Versaflo ™ Powered Air Turbo Spare parts and accessories Part no. Description TR-6710E Particulate filter TR-6820E Particulate filter plus nuisance level organic gases and vapours below OEL (Occupational Exposure Limit), nuisance level acid gases below OEL and hydrogen fluoride gas up to 10 x OEL TR-6110E A1P – Organic gases and vapours (bp > 65°C) and particulates TR-6130E A1B1E1P – Organic gases and vapours (bp > 65°C), inorganic, acid gases and particulates TR-6310E A2P – Organic gases and vapours (bp > 65°C) and particulates TR-6580E A2B2E2K1HgP – Organic gases and vapours (bp > 65°C), inorganic, acid gases, ammonia, mercury vapour and particulates TR-6100FC Filter cover for TR-6100 series filters TR-6300FC Filter cover for TR-6300 series filters TR-6500FC Filter cover for TR-6500 series filters TR-6700FC Filter cover for TR-6700 series filters TR-6800FC Filter cover for TR-6800 series filters TR-6600 Pre-filter TR-662 Spark arrestor TR-830 Intrinsically safe battery (includes TR-838 battery attachment tool) TR-838 Battery attachment tool TR-641E/UK Single station battery charger kit (Europe/UK) TR-644E/UK 4-station battery charger kit (Europe/UK) TR-640 Battery charger cradle TR-626 High durability belt TR-627 Easy clean belt Part no. Description TR-627X Easy clean belt extender BPK-01 Backpack TR-655 Backpack adaptor TR-329 Braces TR-971 Airflow indicator (for checking TR-600/ TR-800 Powered Air Turbo when used with headtops) TR-973 Airflow indicator (for checking TR-600/ TR-800 when used with facepieces) TR-851 Filter latch assembly TR-653 Cleaning and storage kit (for TR-600 and TR-800 Powered Air Turbo) TR-654 Replacement seals (for TR-653 Cleaning and Storage Kit) BT-20 S/L* Lightweight Breathing Tube Small/ Medium or Medium/Long BT-30* Self-adjusting Breathing Tube BT-40* Heavy duty Breathing Tube BT-63* Length-adjusting tight fitting breathing tube BT-64* Heavy Duty tight fitting breathing tube BT-54* Heavy Duty tight fitting breathing tube BT-922 Disposable breathing tube cover (for BT-20S/L, BT-30, BT-40 and BT-54) BT-926 High durability, flames resistant breathing tube cover (for BT-20S/L, BT-30, BT-40 and BT-54) BT-953 Cleaning and storage kit (for BT-63 and BT-64) BT-957 Storage plugs (for all BT-Series breathing tubes) * See breathing tube options table Shelf life 3M ™ Versaflo ™ Powered Air Turbo TR-800 and Filters = 5 years Battery = 6 months (if unused beyond this period, batteries may not provide approximately 750 charge/discharge cycle equivalents during the first year of use while maintaining 80% of their original capacity) The shelf life as defined above remains an indicative and maximum data, subject to many external and non controllable factors. It may never be interpreted as a warranty. Materials Turbo body = Polycarbonate / Polydimethylsiloxane blend Filter cover = Polyamide Battery casing = Polycarbonate / Polydimethylsiloxane blend Weight (including battery but excluding belt and filters) Turbo = 1360g

2. 3M ™ Versaflo ™ Powered Air Turbo Standards and approvals Respiratory EN 12941:1998+A2:2008 – Respiratory protective devices – Powered filtering devices incorporating a helmet or hood EN 12942:1998+A2:2008 – Respiratory protective devices incorporating full face masks, half masks or quarter masks ATEX EN 60079-0:2012 – Explosive atmospheres, Equipment – General Requirements EN 60079-11:2012 – Explosive atmospheres, Equipment protection by intrinsic safety “i” EMC EN 61000-6-4:2007+A1:2011 - Generic standards. Emission standard for industrial environments EN 61000-6-2:2005 Generic standards. Immunity standard for industrial environments Ingress protection IEC 60529:1989+A1:1999+A2:2013 Degrees of protection provided by enclosures (IP Code) RoHS EN 50581:2012 Technical documentation for assessment of electrical/electronic products for RoHS The Certificate and Declaration of Conformity are available at the following website www.3M.com/Respiratory/certs Limitation The 3M ™ Versaflo ™ Powered Air Turbo TR-800 should not be used in the following conditions: Ŕ In atmospheres containing less than 19.5% oxygen Ŕ Confined spaces (lack of ventilation) Ŕ When the risk is considered to be Immediately Dangerous for Life or Health (IDLH) Ŕ Where the contaminant concentration is above the Occupational Exposure Limit defined for the headtop used (see relevant user instructions for the headtop) Product range The TR-800 Powered Air Turbo is available to buy as: Ŕ TR-802E Turbo Unit (includes TR-971 airflow indicator) Ŕ TR-819UK/E Starter Kit includes: TR-802E Turbo Unit, TR-830 Intrinsically Safe Battery, TR-838 Battery Attachment Tool, TR-641UK/E Single Station Battery, TR-971 Airflow Indicator, TR-6310E (A2P) Filter, TR-6300FC Filter Cover, TR-6600 Prefilter (x2), TR-627 Easy Clean Belt and BT-30 Length Adjusting Breathing Tube Ŕ TR-800E-HIK Ready-Pak includes: M-307 Helmet, TR-802E Turbo Unit , TR-830 Standard Battery, TR-838 Battery Attachment Tool, TR-641E Single Station Battery Charger Kit, TR-971 Airflow Indicator, TR-6310E (A2P) Filter, TR-6300FC Filter Cover, TR-6600 Prefilter (x 2), TR-626 High Durability Belt, BT-30 Length Adjusting Breathing Tube, BT-926 High Temperature Breathing Tube Cover and TR-653 Cleaning and Storage Kit Ŕ TR-800E-ECK Ready-Pak includes: S-433L Hood, TR-802E Turbo Unit , TR-830 Standard Battery, TR-838 Battery Attachment Tool, TR-641E Single Station Battery Charger Kit, TR-971 Airflow Indicator, TR-6710E (P) Filter, TR-6700FC Filter Cover, TR-6600 Prefilter (x 2), TR-627 Easy Clean Belt, BT-30 Length Adjusting Breathing Tube, BT-922 Disposable Breathing Tube Cover and TR-653 Cleaning and Storage Kit Ŕ TR-800E-PSK Ready-Pak includes: M-207 Faceshield, TR-802E Turbo Unit, TR-830 Standard Battery, TR-838 Battery Attachment Tool, TR-641E Single Station Battery Charger Kit, TR-971 Airflow Indicator, TR-6310E (A2P) Filter, TR-6300FC Filter Cover, TR-6600 Prefilter (x 2), TR-627 Easy Clean Belt, BT-30 Length Adjusting Breathing Tube, BT-922 Disposable Breathing Tube Cover and TR-653 Cleaning and Storage Kit

3. 3M ™ Versaflo ™ Powered Air Turbo Technical specifications: ATEX Non ‑ mining gas atmospheres (Group II) EN 60079-11 Ex ia IIB T4 Ga ia – intrinsic safety for Equipment protection level Ga IIB – Gas apparatus group T4 – Max. surface temperature 135 ̊C (-20 ̊C ≤ Ta ≤ 55 ̊C) Non ‑ mining dust atmospheres (Group III) EN 60079-11 Ex ia IIIC 135 ̊C Da ia – intrinsic safety for Equipment protection level Da IIIC – Dust apparatus group 135 ̊C – Max surface temperature (-20 ̊C ≤ Ta ≤ 55 ̊C) Note: Ta defines the ambient temperature range within which the Temperature (T) class is defined, according to EN-60079-11 System Classifications and Protection Factors The information in the table below depends on the headtop or facepiece used. Refer to specific datasheet for headtop or facepiece for more information. EN 12941:1998 + A2:2008 EN 12942:1998 + A2:2008 Classification TH2 TH3 TM2 TM3 NPF 50 500 200 2000 Note: The Nominal Protection Factor is a number derived from the maximum percentage of total inward leakage permitted in relevant European Standards for a given class of respiratory protective device. This may not be the level of respiratory protection that can be realistically expected in the workplace by wearers. Many countries apply Assigned Protection Factors (APFs) for example UK and Germany. Employers may apply a value lower than the NPF/APF if deemed applicable. Please refer to EN 529:2005 and National workplace protection guidance for application of these numbers in the workplace. Please contact 3M for further information. Outlet flow characteristics Flow rate In combination with approved headtop In combination with approved facepiece MMDF 1 170 l/min 115 l/min Standard Flow 185 l/min +/- 10 l/min 135 l/min +/- 10 l/min Medium Flow 2 205 l/min +/- 10 l/min 150 l/min +/- 10 l/min High Flow 2 225 l/min +/- 10 l/min 170 l/min +/- 10 l/min Note: 1 MMDF = Stated Manufacturer’s Minimum Design Flow (MMDF) 2 Systems incorporating certain filters must not be used with the Powered Air Turbos operating at medium and/or high flow. These specific systems may display a low flow alarm immediately when used. The specific systems are: FM4 with TR-802E – TR-6110E/TR-6130E must not be used in high flow setting. TR-6310E/TR-6580E must not be used in medium or high flow setting. FM3 with TR-802E – TR-6310E/TR-6580E must not be used in high flow setting. Battery duration (hours) ‑ with approved headtops * Standard flow Medium flow High flow 5.5 – 7.5 4 – 6.5 2 *** – 5.5 Battery duration (hours) ‑ with approved facepieces* Facepiece Standard flow Medium flow High flow 3M ™ Full Facepiece Respirators 6000 Series 3M ™ Full Facepiece Respirators 7907S Series 3M ™ Half Facepiece Respirators 7500 Series 5.5-8 5-6 4-5 3M ™ Vision ™ Full Facepiece Respirator FM4 3M ™ Promask ™ Full Facepiece Respirator FM3 4-6.5 3 ** -5 3 ** -4.5 Battery charge time Less than 3.5 hours IP rating IP 54 (5 = dust protected, 4 = sprayed water from all directions) when using filter cover) IP67 when fitted with cleaning plugs (6 = dust tight, 7 = temporary submersion to a depth of 1m) Storage conditions -30ºC to +50ºC < 90%RH Operating temperature -5ºC to +55ºC Note: This is the operating temperature range for the 3M ™ Versaflo ™ Powered Air Turbo TR-802E when used as part of an approved respiratory protective system * Estimated system duration based on testing with a new battery and a new, clean filter at 20°C. Actual system duration may be extended or shortened depending on system configuration and environment. ** To conserve battery power in high airflow setting, in some headtop/filter configurations, the Powered Air Turbo may automatically step down at this time to the medium airflow setting. If this occurs, a 4hr duration will be achieved. The step down feature can be over-ridden by the user by pressing the flow control button to move the airflow back to the high flow. The low battery alarm and low flow alarm will always operate as described in this user instruction. When either alarm sounds, users must immediately exit the contaminated area.