Safety Datasheet All 01- 04- 07- 75-6 76-6 77-6

3. Safety Data Sheet English Revision date: 04|02|2021 Date of issue: 25|09|2019 Version: 2.0 3 Page Hazmat Absorbent According to Regulation (EC) No. 453/2010 liquidsafety.com/gb 7. 3 Specific end use(s) Specifically designed to absorb aggressive fluids such as acids and bases. For professional use only. Section 8 Exposure controls/personal protection 8.1 Control parameters 8.2 Exposure controls Appropriate engineering controls: Ensure adequate ventilation, especially in confined areas. Personal protective equipment: Not required for normal conditions of use. Materials for protective clothing: Not required for normal conditions of use. Hand protection: Not required for normal conditions of use. Eye protection: Not required for normal conditions of use. Skin and body protection: Not required for normal conditions of use. Respiratory protection: Not required for normal conditions of use. Environmental exposure controls: Do not allow the product to be released into the environment. Consumer exposure controls: Do not eat, drink or smoke during use. Section 9 Physical and chemical properties 9.1 Information on basic physical and chemical properties Physical State: Solid Colour: Yellow Odour: No data available Odour threshold: No data available pH: No data available Relative evaporation rate (butylacetate=l): No data available Melting point: 177 °C (350 °F) Freezing point: No data available Boiling point: 625 °C (1157 °F) Flash point: : No data available Auto-ignition temperature: No data available Decomposition temperature: No data available Flammability (solid, gas): No data available Vapour pressure: No data available Relative Density: 0,9 (Water=l) Relative vapour density at 20 °C: No data available Solubility: Insoluble Partition coefficient: n-octanol/water: No data available Viscosity: No data available Explosive properties: No data available Oxidising properties: No data available Explosive limits: No data available 9.2 Other information VOC content: < 1 % Section 10 Stability and reactivity 10.1 Reactivity Hazardous reactions will not occur under normal conditions. Polypropylene (9003-07-0) Latvia OEL TWA (mg/m³) 5 mg/m 3 Czech Republic Expozi Č ní limity (PEL) (mg/m³) 5 mg/m³ Lithuania IPRV (mg/m³) 10 mg/m³ (not stabilized) Slovakia NPHV (priemerná) (mg/m³) 5,0 mg/m³

5. Safety Data Sheet English Revision date: 04|02|2021 Date of issue: 25|09|2019 Version: 2.0 5 Page Hazmat Absorbent According to Regulation (EC) No. 453/2010 liquidsafety.com/gb 14.4.1 Environmental hazards Other information: No supplementary information available. 14.5 Special precautions for user 14.5.1 Overland transport No additional information available 14.5.2 Transport by sea No additional information available 14.5.3 Air transport No additional information available 14.6 Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code Not applicable Section 15 Regulatory information 15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture 15.1.1 EU-Regulations No REACH Annex XVII restrictions Contains no REACH candidate substance voe content: n< 1 % 15.1.2 National regulations No additional information available 15.2 Chemical safety assessment No additional information available Section 16 Other information Revision date: 25/09/2019 Data sources: REGULATION (EC) No 1272/2008 OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 16 December 2008 on classification, labelling and packaging of substances and mixtures, amending and repealing Directives 67/548/EEC and 1999/45/EC, and amending Regulation (EC) No 1907/2006 SOS EU (REACH Annex II) This information is based on our current knowledge and is intended to describe the product for the purposes of health, safety and environmental requirements only. It should not therefore be construed as guaranteeing any specific property of the product.

2. Safety Data Sheet English Revision date: 04|02|2021 Date of issue: 25|09|2019 Version: 2.0 2 Page Hazmat Absorbent According to Regulation (EC) No. 453/2010 liquidsafety.com/gb First-aid measures after eye contact: Rinse with plenty of water. Remove contact lenses, if present and easy to do. Continue rinsing. Obtain medical attention if irritation develops or persists. First-aid measures after ingestion: Do NOT induce vomiting. Rinse mouth. Immediately call a POISON CENTRE or Doctor/physician. 4.2 Most Important Symptoms and Effects, both Acute and Delayed Symptoms/injuries: Not expected to present a significant hazard under anticipated conditions of normal use. Symptoms/injuries after inhalation: Not expected to be a primary route of exposure. Symptoms/injuries after skin contact: Not expected to present a significant dermal hazard under anticipated conditions of normal use. Symptoms/injuries after eye contact: May cause eye irritation. Symptoms/injuries after ingestion: Ingestion is likely to be harmful or have adverse effects. Chronic symptoms: None expected under normal conditions of use. 4.3 Indication of Any Immediate Medical Attention and Special Treatment Needed If you feel unwell, seek medical advice (show the label where possible). Section 5 Fire fighting measures 5.1 Extinguishing Media Suitable extinguishing media: Use extinguishing media appropriate for surrounding fire. Unsuitable extinguishing media: Do not use a heavy water stream. Use of heavy stream of water may spread fire . 5.2 Special Hazards Arising From the Substance or Mixture Fire hazard: Not considered flammable but may burn at high temperatures. Explosion hazard: Product itself is not explosive. Reactivity: Hazardous reactions will not occur under normal conditions. 5.3 Advice for fire-fighters Precautionary measures fire: Exercise caution when fighting any chemical fire. Fire fighting instructions: Use water spray or fog for cooling exposed containers. Protection during fire fighting: Do not enter fire area without proper protective equipment, including respiratory protection. Section 6 Accidental release measures 6.1 Personal precautions, protective equipment and emergency procedures General measures: No special measures required. 6.1.1 For non-emergency personnel Protective equipment: Use appropriate personal protection equipment (PPE). Emergency procedures: Evacuate unnecessary personnel. 6.1.2 For emergency responders Protective equipment: Equip clean-up crew with proper protection. Emergency procedures: Eliminate ignition sources. Ventilate area. 6.2 Environmental precautions Prevent entry to sewers and public waters . 6.3 Methods and material for containment and cleaning up For containment: Contain and collect as any solid. Methods for cleaning up: Dispose of waste safely. Transfer spilled material to a suitable container for disposal. Contact competent authorities after a spill. 6.4 Reference to other sections See Heading 8. Exposure controls and personal protection. Section 7 Handling and storage 7.1 Precautions for safe handling Additional hazards when processed: None. Precautions for safe handling: Good housekeeping is needed during storage, transfer, handling, and use of this material. Hygiene measures: Handle in accordance with good industrial hygiene and safety procedures. Wash hands and other exposed areas with mild soap and water before eating, drinking or smoking and when leaving work. 7.2 Conditions for safe storage, including any incompatibilities Technical measures: Comply with applicable regulations. Storage conditions: Keep/Store away from direct sunlight, extremely high temperatures and incompatible materials. Incompatible products: Strong oxidisers.

1. Safety Data Sheet English Revision date: 04|02|2021 Date of issue: 25|09|2019 Version: 2.0 1 Page Hazmat Absorbent According to Regulation (EC) No. 453/2010 liquidsafety.com/gb Section 1 Identification of the substance/mixture and of the company/undertaking 1.1 Product Identifier Product form: Fabric Product Name: Hazmat Absorbent Product code: All 01-, 04-, 07-, 75-6, 76-6, 77-6 series products Synonyms: Pad, Roll, non-woven 1.2 Relevant identified uses of the substance or mixture and uses advised against 1.2.1 Relevant identified uses Use of the substance/mixture: Specifically designed to absorb aggressive fluids such as acids and bases. For professional use only. 1.2.2 Uses advised against No additional information available 1.3 Details of the supplier of the safety data sheet Company FyterTech Nonwovens Limited Units C & D Vulcan Business Park Derker Street, Oldham Greater Manchester OL1 4AS 1.4 Emergency Telephone Number Emergency Contact Number FyterTech Nonwovens Limited: 0161 470 8800 Section 2 Hazards identification 2.1 Classification of the Substance or Mixture Classification according to Regulation (EC) No. 1272/2008 [CLP] Not classified Classification according to Directive 67/548/EEC or 1999/45/EC Not classified Adverse physiochemical, human health and environmental effects No additional information available 2.2 Label Elements Labelling according to Regulation (EC) No. 1272/2008 [CLP] No labelling applicable Other hazards not contributing to the classification: Exposure may aggravate those with pre-existing eye, skin, or respiratory conditions. Section 3 Composition/information on ingredients 3.1 Substance Not applicable 3.2 Mixture Section 4 SECTION 4: First aid measures 4.1 Description of First Aid Measures First-aid measures general: Never give anything by mouth to an unconscious person. If you feel unwell, seek medical advice (show the label if possible). First-aid measures after inhalation: Not expected to be a primary route of exposure. First-aid measures after skin contact: Not expected to present a significant dermal hazard under anticipated conditions of normal use. Name Product Identifier % Classification according to Directive 67/548/EEC Polypropylene (CAS No) 9003-07-0 (EC no) 618-352-4 98,2 Not classified Name Product Identifier % Classification according to Regulation (EC) No. 1272/2008 [CLP] Polypropylene (CAS No) 9003-07-0 (EC no) 618-352-4 98,2 Not classified

4. Safety Data Sheet English Revision date: 04|02|2021 Date of issue: 25|09|2019 Version: 2.0 4 Page Hazmat Absorbent According to Regulation (EC) No. 453/2010 liquidsafety.com/gb 10.2 Chemical stability Stable under recommended handling and storage conditions (see section 7). 10.3 Possibility of hazardous reactions Hazardous polymerization will not occur. 10.4 Conditions to avoid Extremely high or low temperatures. Incompatible materials. Ignition sources. 10.5 Incompatible materials Strong oxidizers. 10.6 Hazardous decomposition products Carbon oxides (CO, CO 2). Section 11 Toxicological information 11.1 Information on toxicological effects Acute toxicity: Not classified Skin corrosion/irritation: Not classified Serious eye damage/irritation: Not classified Respiratory or skin sensitisation: Not classified Germ cell mutagenicity: Not classified Carcinogenicity: Not classified Reproductive toxicity: Not classified Specific target organ toxicity (single exposure): Not classified Specific target organ toxicity (repeated exposure): Not classified Aspiration hazard: Not classified Section 12 Ecological information 12.1 Toxicity No additional information available 12.2 Persistence and degradability No additional information available 12.3 Bioaccumulative potential No additional information available 12.4 Mobility in soil No additional information available 12.5 Results of PBT and vPvB assessment No additional information available 12.6 Other adverse effects Other information: Avoid release to the environment. Section 13 Disposal considerations 13.1 Waste treatment methods Waste disposal recommendations: Dispose of waste material in accordance with all local, regional, national, and international regulations. Ecology - waste materials: Avoid release to the environment. Section 14 Transport information In accordance with ADR /RID/ IMDG / IATA / ADN 14.1 UN number No dangerous good in sense of transport regulations 14.2 UN proper shipping name Not applicable 14.3 Transport hazard class(es) Not applicable 14.4 Packing group Not applicable