3m_supplied_air_respirator_system_s200+_-_brochure

4. Half Face 3M™ 6000 HM Full Face 3M™ 6000 FF Half Face 3M™ 6500 HM Full Face 3M™ 7907S FF Half Face 3M™ 7500 HM Select Your Individual Respirator System: 1 2 3 4 5 1 2 Select your S-200+ air delivery unit Select your half face or full face mask Select your filters (for use in dual-mode) Select the appropriate air supply tube Select your accessories and air tools (optional) The S-200+ System can be combined with a wide range of 3M Masks: Select a Half Face or Full Face Mask Select the S-200+ Air Delivery Unit

8. Part Number Description Standards Tested and approved to EN 14594:2005. When used with a 3M™ recommended Full Face mask the product meets the requirements for a class 4A/B device. When used with a 3M™ recommended Half Face mask the product meets the requirements for a class 3A/B device. CE Marked. ATEX Tested System has been assessed in accordance with the requirements of the ATEX directive and in accordance with EN 13463-1 for non-electrical equipment. The equipment is suitable for use in IIB 2GD environments under certain conditions. Valid only when fitted with a 3M™ 308-00-72P Antistatic Compressed Air Supply Tube. Please see all relevant user information for further details. Nominal Protection Factor (NPF) 3M Half Face masks (Class 3A/B) = 200 3M Full Face masks (Class 4A/B) = 2000 Inlet Pressure Pressure range: 3.0-7.0 Bar Pressure range (with Auxiliary air tool connected): 4.5-7.0 Bar Maximum Pressure: 10 Bar Outlet Flow Characteristics Manufacturer’s Minimum Design Flow (MMDF): 120l/min Maximum Flow: >350l/min Storage Conditions -10°C to +50°C <90% Relative Humidity Operating temperature 0°C to +40°C <90% Relative Humidity Weight 690g (including regulator, belt and breathing tube) Connections Inlet Port: CEJN 346 Auxiliary Port: ¼ inch BSP The compressed air supply used to operate the S-200+ Regulator must comply with the quality requirements of EN 12021 Limitations The S-200+ Supplied Air Respirator system should not be used in the following conditions: • In atmospheres containing less than 19.5% oxygen • Confined spaces (lack of ventilation) • When the risk is considered to be immediately dangerous for life or health (IDLH) • Where the contaminant concentration is above the Threshold Limit Value defined for the facepiece used Technical Specification Spare Parts and Accessories Scan this QR code with your smartphone for more information on the Supplied Air Respirator System S-200+ Or visit: www.3M.eu/S-200+ Note: 3M does not accept responsibility or liability, direct or consequential, arising from reliance upon any information provided and the user should determine the suitability of the products for their intended use. Nothing in this statement will be deemed to exclude or restrict 3M’s liability for death or personal injury arising from its negligence or fraudulent misrepresentation. Part Number D escription S-212 Regulator S-222 Breathing Tube C-340 Overflow Valves C-321 Spray Gun Adaptor FCB-01 Flow Check Bag 301-00-62P5 Belt 308-00-30P 10m Standard Duty CAST 308-00-31P 30m Standard Duty CAST 308-00-40P 7.5m Light Duty CAST Part Number D escription 308-00-72P 10m Standard Duty, Anti-static, Heat Resistant CAST 530-12-81P3 Socket and Plug Set – Rectus 95 312-03-01P3 2-way Branch Set 312-03-00P3 3-way Branch Set ACU-03 Aircare Filtration Unit – Wall mounted ACU-04 Aircare Filtration Unit – Free standing 105 Cleaning Wipes 107 Storage Bag 3M Personal Safety Division 3M United Kingdom 3M Centre Cain Road, Bracknell Berkshire RG12 8HT Tel: 0870 60 800 60 www.3M.EU/PPESafety Please recycle. Printed in UK. © 3M 2014. All rights reserved.

6. 3M™ 107 Carry Bag Premium storage solution for your storing your S-200+ Air Delivery Unit, mask, filters, air tools and accessories: • Premium quality materials/fasteners • Rigid panels for durability and robustness, yet still lightweight • Place name holder for customisation • Adjustable carry strap to make carrying PPE and equipment easier Air Filtration Unit 3M™ Aircare™ Filtration Unit ACU-03 (Wall mounted) Branch Set 2-Way Branch Set 3/8” female pipe thread BSP, incl. 3/8” BSP adapters Part No: 312-03-01P3 Air Filtration Unit 3M™ Aircare™ Filtration Unit ACU-04 (Free standing) Branch Set 3-Way Branch Set 3/8” BSP, incl. 3/8” BSP adapters Part No: 312-03-00P3 Branch Sets The branch sets allow you to connect two or three users to the same 3M Aircare™ Filtration Unit. 3M™ Aircare™ Filtration Unit The 3M™ Aircare™ Filtration Unit can be combined with the S-200+ Supplied Air Respirator System. The three-stage filtration system supplies highest quality air to the Supplied Air Respirator System and compressed air tools by removing water and oil aerosols, particles and odours from the facility-supplied compressed air. 5 Accessories

2. Introduction The 3M™ Supplied Air Respirator System S-200+ is a comfortable and versatile supplied air respirator system for use with a wide range of 3M™ Half and Full Face Reusable Masks. The S-200+ System can be used as a standard airline respirator system or in dual-mode with filter back-up when air supply is disconnected. Engineered to deliver additional comfort and security, the S-200+ features double- action safety couplings to help minimise the risk of accidental disconnection during use and an adjustable airflow feature so you can control the air across your face for maximum comfort. Applications The S-200+ System, when used with an approved 3M™ Face Mask provides respiratory protection against: • Particles e.g. fine dusts, aerosols, paint spray or metal fume • Gases and vapours • Particles, gases and vapours combined 3M S-200+ Supplied Air Respirator System Engineered for comfort and security Application T ypical Industry Spray Painting General Transport Automotive & Aerospace Metal Fabrication Shipbuilding Oil and Gas Glass Fibre Fabrication Boat Building Wind Turbine Manufacturing Powder Coating Metal Fabrication Material Handling Pharmaceutical Chemical Agrochemical Laboratory New The ™

7. 3M™ Accuspray™ System The 3M™ Accuspray™ System is compatible for use with the 3M™ S-200+ Supplied Air Respirator System. • Gives like-new spray gun performance on demand • Innovative technology gives efficient and economical application of primer with each atomising head delivering a large usable pattern • Very low overspray and exceptional atomisation For full performance details and user instructions, please see all information for use of the 3M™ Accuspray™ System before use. Auxiliary Air Tools A wide range of air tools can be fitted to the 3M™ S-200+ Supplied Air Respirator System eliminating the need for multiple airlines when working. The chart below shows the amount of air available for auxiliary air tool use when the 3M™ S-200+ Supplied Air System is set to its minimum flow setting. 3M recommends that auxiliary air tools are only used in combination with the S-200+ Supplied Air System between 4.5 and 7 Bar. Note: Increased flow to the mask will reduce the air available to the auxiliary air tool at any given pressure. Always ensure that the air tool to be used with the S-200+ is compatible for use and can deliver the performance required. 700 600 500 400 300 200 100 0 4.5 5.25 6 6 .5 7 Pressure Range for Auxiliary Air Tool Use (Bar) Total Available Air (Litres per Minute) Air Tool Air Supply Facepiece Air Supply

1. SM The Power To Protect Your World 3M™ Supplied Air Respirator System S200+ 3M Personal Safety Division Work in a World of Comfort

3. * V alid only when fitted with a 3M 308-00-72P Antistatic Compressed Air Supply Tube. ** W hen used with a 3M™ recommended Full Face mask the product meets the requirements for a class 4A /B device. W hen used with a 3M™ recommended Half Face mask the product meets the requirements for a class 3A /B device. Features and Benefits Cool and Comfortable • Lightweight and balanced system with a constant flow of air across the face for a cooler and more comfortable wear Adjustable Airflow • Lockable airflow adjustment knob giving you full control of a range of input pressure NEW! Double Action Couplings • Help to minimise the risk of accidental disconnection during use giving you enhanced confidence in protection • Stainless Steel CAST Connection, offering improved corrosion resistance in tough conditions NEW! Flow Check Bag FCB-01 • The S-200+ includes a Flow Check Bag allowing you to conduct a simple pre-use check to ensure that the correct amount of air is being delivered - giving you peace of mind NEW! ATEX Tested • Assessed in accordance with the requirements of the ATEX directive and in accordance with EN13463-1 for non- electrical equipment.* • Suitable for use in IIB 2GD environments under certain conditions. Please see relevant user instructions for further details. Quick and Easy Maintenance • Easy to maintain, spare parts are quick, easy and intuitive to replace Top Performance • Tested and approved to EN 14594:2005 • Meets the highest level of protection, Class 4B for continuous flow supplied air respirators when fitted to a full face mask** Easy Movement • Low profile, narrow-bore breathing tube for ease of movement • Helps to reduce interference with your work Easy to Connect • Robust, proven bayonet connection to the facepiece and filter provides easy fitting with confidence of security

5. Select your filters (if used in Dual Mode) The 3M™ Respirator System S-200+ can be used as a standard airline respirator or in dual-mode with a wide range of 3M™ filters that provide continuous protection when the air supply is disconnected. Part No: 530-12-81P3 Note: you also need the 3/8” BSP Rectus 95 Coupling Set 4 Select your Air Supply Tube Gas & Vapour Filter 3M™ 6055 Organic Gases and Vapours (boiling point >65°C) up to 5000ppm (A2) Combination Filter 3M™ 6096 Organic Gases and Vapours (boiling point >65°C), Mercury and Particulates ( A1HgP3R) Gas & Vapour Filter 3M™ 6054 Ammonia and Ammonia based Gases and vapours (K1) Gas & Vapour Filter 3M™ 6051 Organic Gases and Vapours (boiling point >65°C) up to 1000ppm (A1) Gas & Vapour Filter 3M™ 6075 Organic Gases and Vapours (boiling point >65°C) plus formaldehyde (up to 10ppm) ( A1) Particulate Filter 3M™ 2138 Particulate Filter + nuisance vapours (P3R) Particulate Filter 3M™ 5935 Particulate Filter (P3R) Particulate Filter 3M™ 2135 Particulate Filter (P3R) Gas & Vapour Filter 3M™ 6059 Combination Organic Gases and Vapours (boiling point >65°C), Inorganic, Acid and Ammonia based Gases (ABEK1) Gas & Vapour Filter 3M™ 6057 Combination Organic Gases and Vapours (boiling point >65°C), Inorganic and Acid Gases (ABE1) Filter Retainer 3M™ 501 5000 Series Filters can be used with 6000 Series Filters for combined gas and particulate protection in conjunction with a 501 Filter Retainer Part No: 308-00-40P 7.5m Light Duty CAST Part No: 308-00-30P 10m Standard Duty CAST Part No: 308-00-31P 30m Standard Duty CAST Part No: 308-00-72P 10m Standard Duty, anti- static, heat resistant CAST 3