Speedglas_G501_care_maintenance_poster CE

1. 3M Science. Applied to life. ™ 3M ™ Speedglas ™ Heavy Duty Welding Helmet G5-01 To optimize the effective lifetime of your welding equipment and avoid the additional cost of replacement, regular maintenance is important. Replace all damaged parts immediately to help ensure intended degree of protection. Below is a helpful overview; always read and follow User Instructions. 1 Helmet and headband. Inspect for cracks or any damaged parts. Replace if needed. 2 Protection plates. To help provide the best possible vision, they should be clean and without scratches. 3 Face seal. If the face seal is damaged, there is a risk that contaminated air will get inside the helmet. Verify it’s in place and free from splits and tears. 4 Welding filter. Ensure that the low battery indicator is not flashing and check that the sensors are clean and uncovered. 5 Breathing tube. Confirm that the tube is undamaged and not leaking any air. To extend the life of the breathing tube, use a tube cover or a heavy- duty breathing tube. Before use Spare parts and consumables After use 1 Clean the helmet. Wipe with a moist tissue or cloth, both inside and outside the helmet. If you suspect that the inside of the breathing tube is dirty, it must be changed. DO NOT rinse, immerse in water, or clean with solvents. 2 Face seal and sweatband. Remove for additional cleaning as needed and replace if they have splits or tears or whenever they become unhygienic. 3 Protection plates and visor plate. Clean with a soft cloth and replace if any pits or scratches occur. 4 Breathing tube. Replace if damaged, deformed or leaking any air. 5 Storage. Store the helmet in a dry, clean area away from direct sunlight, high temperatures and solvents. 16 92 10 16 92 11 16 92 05 16 92 00 16 90 35 16 90 21 16 90 23 16 91 00 16 90 30 16 90 42 16 90 41 16 90 43 16 90 20 16 90 22 61 11 90 61 11 00 61 40 00 61 11 95 61 05 00 61 30 00 61 05 01 61 01 95 16 90 20 16 90 40 19 71 55 61 37 00 61 37 01 61 60 01 19 80 16 19 80 17 19 80 18 61 60 02 61 60 03 53 62 10 53 62 11 61 60 00 61 32 00 52 60 00 52 70 00 52 70 01 52 70 70 61 00 20 61 00 30 52 80 25 52 80 26 52 80 27 17 10 20 17 10 21 17 10 22 17 10 23 17 10 24 60 10 00 CR2450 60 20 00 17 10 35 79 01 05 12 60 00 61 00 11 11 00 10 11 00 11 11 00 12 11 00 13 16 90 20 Head protection in fabric 16 90 21 Head protection High Vis 16 90 22 Head protection in leather 16 90 23 Head protection in fabric (large) 16 90 24 Scrape guard (not shown) 16 90 30 Shroud 16 90 35 Extended cover kit (shroud and large head cover in fabric) 16 90 41 Neck protection in fabric (small) 16 90 42 Neck protection in fabric (large) 16 90 43 Neck protection in leather 16 92 00 Task light, incl mounting parts and cables 16 92 05 Protection plate for task light, pkg. of 5 16 92 10 Long power cable for task light 16 92 11 Short power cable for task light 16 92 23 Pouch with Adflo battery, for task light when using supplied air regulator (not shown) 11 00 10 Passive welding filter lens shade 10 (90x110) 11 00 11 Passive welding filter lens shade 11 (90x110) 11 00 12 Passive welding filter lens shade 12 (90x110) 11 00 13 Passive welding filter lens shade 13 (90x110) 12 60 00 Inner cover plate for passive filter 16 90 20 Head protection in fabric (small) 16 90 40 Neck protection rigid 17 10 20 Magnifying lens 1.0X 17 10 21 Magnifying lens 1.5X 17 10 22 Magnifying lens 2.0X 17 10 23 Magnifying lens 2.5X 17 10 24 Magnifying lens 3.0X 17 10 35 Magnifying lens holder 19 71 55 Hinge mechanism, 1 pair 19 80 16 Sweatband (towelling), pkg of 3 19 80 17 Sweatband (fleecy cotton), pkg of 3 19 80 18 Sweatband (leather) 52 60 00 Outer protection plate (standard), pkg of 10 52 70 00 Outer protection plate (scratch), pkg of 10 52 70 01 Outer protection plate (scratch +), pkg of 10 52 70 70 Outer protection plate (heat), pkg of 10 52 80 25 Inner cover plate, pkg of 5 52 80 26 Inner cover plate, +1 shade, pkg of 5 52 80 27 Inner cover plate, +2 shade, pkg of 5 53 62 10 Cushion part for headband G5-01 53 62 11 Large head rest 60 10 00 Battery holder 60 20 00 Battery CR2450 61 00 11 Speedglas passive welding filter kit G5-01 (shade 11) 61 00 20 Speedglas welding filter G5-01TW 61 00 30 Speedglas welding filter G5-01VC 61 01 95 Outer shield 61 05 00 Inner visor, including visor frame 61 05 01 Outer visor, including front cover 61 11 90 Welding helmet G5-01, without welding filter, without neck or head protection 61 11 95 Inner shield with airduct and airflow controls (including visor frame) 61 30 00 Visor plate, anti-fog and hardcoated, pkg. of 5 61 32 00 Headband with assembly parts 61 37 00 Airduct breathing tube (short) incl. holder 61 37 01 Holder for breathing tube 61 40 00 Face seal 61 60 00 Pivot and sliding mechanism, including pivot knobs 61 60 01 Pivot rings for outer shield 61 60 02 Pivot knobs 61 60 03 Headband back part 79 20 00 Consumable starter kit G5-01, including sweatband, face seal, visor plate, inner and outer cover plates. 79 01 05 Carry Bag 61 78 00 Helmet G5-01, without welding filter, with 3M ™ Adflo ™ Powered Air Repirator 61 78 09 Helmet G5-01, without welding filter, with 3M ™ Adflo ™ Powered Air Repirator and consumable starter kit 61 11 00 Welding helmet G5-01, without welding filter Part No Description Part No Description Part No Description facebook.com/3MSpeedglas www.speedglas.com Instagram.com/3MSpeedglas youtube.com/3MSpeedglas Respiratory Protection Products: These respirators help protect against certain airborne contaminants. Before use, the wearer must read and understand the User Instructions provided as a part of the product packaging. A written respiratory protection program must be implemented meeting all the requirements of OSHA 1910.134 including training, fit testing and medical evaluation. In Canada, CSA standards Z94.4 requirements must be met and/or requirements of the applicable jurisdiction, as appropriate. Improper use may result in injury, illness or death. For correct use, see supervisor or User Instructions, or call 3M PSD Technical Service in USA at 1-800-243-4630 and in Canada at 1-800-267-4414.