52160_52161ds

9. Technical_Description_tyvek-500-accessory-typt31swhl0.pdf printed on February 25, 2021 page of 9 9

1. Technical_Description_tyvek-500-accessory-typt31swhl0.pdf printed on February 25, 2021 page of 1 9 Tyvek® 500 Accessory DuPont™ Tyvek® 500 Trousers model PT31L0. Elasticated waist. Stitched internal seams. No pockets. White. Certifications Certified according to Regulation (EU) 2016/425 Partial body chemical protective clothing, Category III, Type PB [6-B] EN 14126 (barrier to infective agents) Antistatic treatment (EN 1149-1) - on both sides; see footnotes Packaging(Quantity/Box) 50 per box, bulk packed. EN 14126 PB[6] CAT III Technical Data Sheet Tyvek® 500 Accessory, TYPT31SWHL0 Product Size Article Number Additional info MD D13496109 LG D13395741 XL D13395735 2X D13496097 Full Part Number: TYPT31SWHL0

8. Technical_Description_tyvek-500-accessory-typt31swhl0.pdf printed on February 25, 2021 page of 8 9 Important Note The permeation data published have been generated for DuPont by independent accredited testing laboratories according to the test method applicable at that time (EN ISO 6529 (method A and B), ASTM F739, ASTM F1383, ASTM D6978, EN369, EN 374-3) The data is typically the average of three fabrics samples tested. All chemicals have been tested at an assay of greater than 95 (w/w) % unless otherwise stated. The tests were performed between 20 °C and 27 °C and at environmental pressure unless otherwise stated. A different temperature may have significant influence on the breakthrough time. Permeation typically increases with temperature. Cumulative permeation data have been measured or have been calculated based on minimum detectable permeation rate. Cytostatic drugs testing has been performed at a test temperature of 27°C according to ASTM D6978 or ISO 6529 with the additional requirement of reporting a normalized breakthrough time at 0.01 μg/cm²/min. Chemical warfare agents (Lewisite, Sarin, Soman, Mustard, Tabun and VX Nerve Agent) have been tested according to MIL-STD-282 at 22°C or according to FINABEL 0.7 at 37°C. Permeation data for Tyvek® is applicable to white Tyvek® 500 and Tyvek® 600 only and is not applicable for other Tyvek® styles or colours. Permeation data are usually measured for single chemicals. The permeation characteristics of mixtures can often deviate considerably from the behaviour of the individual chemicals. The permeation data for gloves published have been generated according to ASTM F739 and to ASTM F1383. The degradation data for gloves published have been generated based on a gravimetric method. This degradation testing exposes one side of the glove material to the test chemical for four hours. The percent weight change after exposure is measured at four time intervals: 5, 30, 60 and 240 minutes. Degradation Ratings: E: EXCELLENT (0-10% Weight Change) G: GOOD (11-20% Weight Change) F: FAIR (21-30% Weight Change) P: POOR (31-50% Weight Change) NR: NOT RECOMMENDED (Above 50% Weight Change) NT: NOT TESTED Degradation is the physical change in a material after chemical exposure. Typical observable effects may be swelling, wrinkling, deterioration, or delamination. Strength loss may also occur. Please use the permeation data provided as a part of the risk assessment to assist with the selection of a protective fabric, garment, glove or accessory suitable for your application. Breakthrough time is not the same as safe wear time. Breakthrough times are indicative of the barrier performance, but results can vary between the test methods and laboratories. Breakthrough time alone is insufficient to determine how long a garment may be worn once the garment has been contaminated. Safe user wear time may be longer orshorter than the breakthrough time depending on the permeation behaviour of the substance, the toxicity of the substance, working conditions and the exposure conditions (e.g. temperature, pressure, concentration, physical state). Latest Update Permeation Data: 5/5/2020 The information provided herein corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials or additives or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. The information provided herein corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials or additives or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as a license to operate under or a recommendation to infringe any patent rights. This garment and/or fabric are not flame resistant and should not be used around heat, open flame, sparks or in potentially flammable environments. Working in Ex-Zones: Please take this into account for your risk-assessment that the attached socks may isolate the wearer. There is the possibility that the garment and wearer cannot by grounded via the shoes and other measures for grounding the garment and the wearer are required.

3. Technical_Description_tyvek-500-accessory-typt31swhl0.pdf printed on February 25, 2021 page of 3 9 COMFORT Property Test Method Typical Result EN Air Permeability (Gurley method) ISO 5636-5 Yes N/A Air Permeability (Gurley method) ISO 5636-5 < 45 s N/A Thermal Resistance, Rct EN 31092/ISO 11092 16.3*10 m *K/W -3 2 N/A Thermal Resistance, clo value EN 31092/ISO 11092 0.105 clo N/A Water Vapour Resistance, Ret EN 31092/ISO 11092 11.3 m *Pa/W 2 N/A  According to EN 14126 2  Front Tyvek ® / Back 5  Larger than >  Smaller than <  Not Applicable N/A PENETRATION AND REPELLENCY Property Test Method Typical Result EN Repellency to Liquids, Sodium Hydroxide (10%) EN ISO 6530 >95 % 3/3 1 Repellency to Liquids, Sulphuric Acid (30%) EN ISO 6530 >95 % 3/3 1 Resistance to Penetration by Liquids, Sodium Hydroxide (10%) EN ISO 6530 <1 % 3/3 1 Resistance to Penetration by Liquids, Sulphuric Acid (30%) EN ISO 6530 <1 % 3/3 1  According to EN 14325 1  Larger than >  Smaller than < BIOLOGICAL BARRIER Property Test Method Typical Result EN Resistance to Penetration by Biologically Contaminated Aerosols ISO/DIS 22611 Pass 1/3 2 Resistance to Penetration by Blood and Body Fluids using Synthetic Blood ISO 16603 3,5 kPa 3/6 2 Resistance to Penetration by Blood-borne Pathogens using Bacteriophage Phi-X174 ISO 16604 Procedure C No classification No classification 2 Resistance to Penetration by Contaminated Liquids EN ISO 22610 ≤ 15 min 1/6 2 Resistance to Penetration by Contaminated Solid Particles ISO 22612 Pass 1/3 2  According to EN 14126 2  Larger than >  Smaller than < CLEANLINESS Property Test Method Typical Result EN  Front Tyvek ® / Back 5  Larger than >  Smaller than <  Not Applicable N/A  Standard Deviation STD DEV

2. Technical_Description_tyvek-500-accessory-typt31swhl0.pdf printed on February 25, 2021 page of 2 9 PHYSICAL PROPERTIES Property Test Method Typical Result EN Abrasion Resistance ⁷ EN 530 Method 2 >100 cycles 2/6 1 Basis Weight DIN EN ISO 536 41.5 g/m 2 N/A Colour N/A (598) White N/A Exposure to high Temperature N/A (598) Melting point ~135 °C N/A Exposure to low Temperature N/A (598) Flexibility retained down to -73 °C N/A Flex Cracking Resistance ⁷ EN ISO 7854 Method B >100000 cycles 6/6 1 Flex Cracking Resistance at -30°C EN ISO 7854 Method B >4000 cycles N/A Puncture Resistance EN 863 >10 N 2/6 1 Resistance to water penetration DIN EN 20811 >10 kPa N/A Surface Resistance at RH 25%, inside ⁷ EN 1149-1 < 2,5 • 10 Ohm 9 N/A Surface Resistance at RH 25%, outside ⁷ EN 1149-1 < 2,5 • 10 Ohm 9 N/A Tensile Strength (MD) DIN EN ISO 13934-1 >30 N 1/6 1 Tensile Strength (XD) DIN EN ISO 13934-1 >30 N 1/6 1 Trapezoidal Tear Resistance (MD) EN ISO 9073-4 >10 N 1/6 1 Trapezoidal Tear Resistance (XD) EN ISO 9073-4 >10 N 1/6 1  According to EN 14325 1  According to EN 14126 2  According to EN 1073-2 3  According to EN 14116 4   According to EN 11612 12  Front Tyvek ® / Back 5  Based on test according to ASTM D-572 6  See 7 Instructions for Use for further information, limitations and warnings  Larger than >  Smaller than <  Not Applicable N/A  Standard Deviation STD DEV GARMENT PERFORMANCE Property Test Method Typical Result EN Seam Strength EN ISO 13935-2 >50 N 2/6 1 Shelf Life ⁷ N/A (598) 10 years 6 N/A Type PB 6: Partial Body Protection EN 13034 Pass N/A  According to EN 14325 1  According to EN 1073-2 3   According to EN 11612 12   According to EN 11611 13  Front Tyvek ® / Back 5  Based on test according to ASTM D-572 6  See Instructions for Use for 7 further information, limitations and warnings  Based on the average of 10 suits, 3 activities, 3 probes 11  Larger than >  Smaller than <  Not Applicable N/A  Based on lowest single value *

7. Technical_Description_tyvek-500-accessory-typt31swhl0.pdf printed on February 25, 2021 page of 7 9 Permeation Data for Tyvek® 500 Accessory Hazard / Chemical Name Physical State CAS BT Act BT 0.1 BT 1.0 EN SSPR MDPR Cum 480 Time 150 ISO Sulfuric acid (18%) Liquid 7664-93-9 >240 >240 >480 6 <0.05 0.05 Sulfuric acid (18%) Liquid 7664-93-9 >240 >480 6 <0.05 0.05 Sulfuric acid (30%) Liquid 7664-93-9 >10 >240 >240 5 <0.05 0.05 Sulfuric acid (30%) Liquid 7664-93-9 >240 >240 5 <0.05 0.05 Sulfuric acid (50%) Liquid 7664-93-9 >30 >60 3 38 0.01 Sulfuric acid (50%) Liquid 7664-93-9 imm >30 >60 3 38 0.01 Sulfuric acid dimethyl ester Liquid 77-78-1 imm imm >160 0.02 Sulfuric acid dimethyl ester Liquid 77-78-1 imm imm imm >160 0.02 Thiotepa (10 mg/ml) Liquid 52-24-4 imm imm na 0.001 Thiotepa (10 mg/ml) Liquid 52-24-4 imm imm imm na 0.001 Vincristine sulfate (1 mg/ml) Liquid 2068-78-2 >240 >240 6 <0.001 0.001 Vincristine sulfate (1 mg/ml) Liquid 2068-78-2 >240 >240 >240 6 <0.001 0.001 Vinorelbine (0.1 mg/ml) Liquid 71486-22-1 >240 >240 6 <0.0209 0.00209 Vinorelbine (0.1 mg/ml) Liquid 71486-22-1 >240 >240 >240 6 <0.0209 0.00209 (Actual) Breakthrough time at MDPR [mins] BTAct Normalized breakthrough time at 0.1 μg/cm²/min [mins] BT0.1 Normalized breakthrough time at 1.0 μg/cm²/min [mins] BT1.0 Classification according to EN 14325 EN Steady state permeation rate [μg/cm²/min] SSPR Minimum detectable permeation rate [μg/cm²/min] MDPR Cumulative permeation mass after 480 mins [μg/cm²] CUM480 Time to reach cumulative permeation Time150 mass of 150 μg/cm² [mins] Classification according to ISO 16602 ISO Chemical abstracts service registry number CAS Minute min Larger than > Smaller than < Immediate (< 10 min) imm Not tested nm Saturated solution sat Not Applicable N/A Not attained na General purpose reagent grade GPR grade Based on lowest single value * Actual breakthrough time; normalized breakthrough time is not available 8 Degradation after 5 min DOT5 Degradation after 30 min DOT30 Degradation after 60 min DOT60 Degradation after 240 min DOT240 Normalized breakthrough time at 0.1 μg/cm²/min [mins] acc. ASTM F1383 BT1383

4. Technical_Description_tyvek-500-accessory-typt31swhl0.pdf printed on February 25, 2021 page of 4 9 Permeation Data for Tyvek® 500 Accessory Hazard / Chemical Name Physical State CAS BT Act BT 0.1 BT 1.0 EN SSPR MDPR Cum 480 Time 150 ISO Acetic acid (30%) Liquid 64-19-7 imm imm imm 13.5 0.001 Acetic acid (30%) Liquid 64-19-7 imm imm 13.5 0.001 Ammonium hydroxide (16%) Liquid 1336-21-6 imm imm imm 20.3 0.005 Ammonium hydroxide (28% - 30%) Liquid 1336-21-6 imm imm 16.7 0.014 Ammonium hydroxide (28% - 30%) Liquid 1336-21-6 imm imm imm 16.7 0.014 Carboplatin (10 mg/ml) Liquid 41575-94-4 >240 >240 >240 5 <0.001 0.001 Carboplatin (10 mg/ml) Liquid 41575-94-4 >240 >240 5 <0.001 0.001 Carmustine (3.3 mg/ml, 10 % Ethanol) Liquid 154-93-8 imm >240 5 <0.3 0.001 Carmustine (3.3 mg/ml, 10 % Ethanol) Liquid 154-93-8 imm imm >240 5 <0.3 0.001 Caustic ammonia (16%) Liquid 1336-21-6 imm imm imm 20.3 0.005 Caustic ammonia (16%) Liquid 1336-21-6 imm imm 20.3 0.005 Caustic ammonia (28% - 30%) Liquid 1336-21-6 imm imm imm 16.7 0.014 Caustic soda (10%) Liquid 1310-73-2 >480 >480 6 <0.005 0.005 Caustic soda (10%) Liquid 1310-73-2 >240 >480 >480 6 <0.005 0.005 Caustic soda (40%) Liquid 1310-73-2 imm >30 >240 5 <0.005 0.005 Caustic soda (40%) Liquid 1310-73-2 >30 >240 5 <0.005 0.005 Caustic soda (50%) Liquid 1310-73-2 >30 >240 6 0.85 0.01 Caustic soda (50%) Liquid 1310-73-2 imm >30 >240 6 0.85 0.01 Caustic soda (>95%, solid) Solid 1310-73-2 >480 >480 >480 6 <0.01 0.01 Caustic soda (>95%, solid) Solid 1310-73-2 >480 >480 6 <0.01 0.01 Cisplatin (1 mg/ml) Liquid 15663-27-1 >240 >240 5 <0.0002 0.0002 Cisplatin (1 mg/ml) Liquid 15663-27-1 >240 >240 >240 5 <0.0002 0.0002 Cyclo phosphamide (20 mg/ml) Liquid 50-18-0 >240 >240 5 <0.002 0.002 Cyclo phosphamide (20 mg/ml) Liquid 50-18-0 >240 >240 >240 5 <0.002 0.002 Dimethyl sulfate Liquid 77-78-1 imm imm imm >160 0.02 Doxorubicin HCl (2 mg/ml) Liquid 25136-40-9 >240 >240 5 <0.003 0.003 Doxorubicin HCl (2 mg/ml) Liquid 25136-40-9 >240 >240 >240 5 <0.003 0.003 Ethane 1,2-diol Liquid 107-21-1 imm imm 6.6 0.002 Ethane 1,2-diol Liquid 107-21-1 imm imm imm 6.6 0.002 (Actual) Breakthrough time at MDPR [mins] BTAct Normalized breakthrough time at 0.1 μg/cm²/min [mins] BT0.1 Normalized breakthrough time at 1.0 μg/cm²/min [mins] BT1.0 Classification according to EN 14325 EN Steady state permeation rate [μg/cm²/min] SSPR Minimum detectable permeation rate [μg/cm²/min] MDPR Cumulative permeation mass after 480 mins [μg/cm²] CUM480 Time to reach cumulative permeation Time150 mass of 150 μg/cm² [mins] Classification according to ISO 16602 ISO Chemical abstracts service registry number CAS Minute min Larger than > Smaller than < Immediate (< 10 min) imm Not tested nm Saturated solution sat Not Applicable N/A Not attained na General purpose reagent grade GPR grade Based on lowest single value * Actual breakthrough time; normalized breakthrough time is not available 8 Degradation after 5 min DOT5 Degradation after 30 min DOT30 Degradation after 60 min DOT60 Degradation after 240 min DOT240 Normalized breakthrough time at 0.1 μg/cm²/min [mins] acc. ASTM F1383 BT1383

5. Technical_Description_tyvek-500-accessory-typt31swhl0.pdf printed on February 25, 2021 page of 5 9 Permeation Data for Tyvek® 500 Accessory Hazard / Chemical Name Physical State CAS BT Act BT 0.1 BT 1.0 EN SSPR MDPR Cum 480 Time 150 ISO Ethylene glycol Liquid 107-21-1 imm imm imm 6.6 0.002 Etoposide (Toposar®, Teva) (20 mg/ml, 33.2 % (v/v) Ethanol) Liquid 33419-42-0 >240 >240 5 <0.01 <0.01 Etoposide (Toposar®, Teva) (20 mg/ml, 33.2 % (v/v) Ethanol) Liquid 33419-42-0 >240 >240 >240 5 <0.01 <0.01 Fluorouracil, 5- (50 mg/ml) Liquid 51-21-8 imm >30 2 na 0.001 Fluorouracil, 5- (50 mg/ml) Liquid 51-21-8 imm imm >30 2 na 0.001 Formic acid (30%) Liquid 64-18-6 imm imm imm nm 0.001 Formic acid (30%) Liquid 64-18-6 imm imm nm 0.001 Ganciclovir (3 mg/ml) Liquid 82410-32-0 >240 >240 >240 5 <0.005 0.005 Ganciclovir (3 mg/ml) Liquid 82410-32-0 >240 >240 5 <0.005 0.005 Gemcitabine (38 mg/ml) Liquid 95058-81-4 imm >60 >240 5 <0.4 0.005 Gemcitabine (38 mg/ml) Liquid 95058-81-4 >60 >240 5 <0.4 0.005 Glycerine Liquid 56-81-5 >240 >480 >480 6 0.03 0.01 Glycerol Liquid 56-81-5 >480 >480 6 0.03 0.01 Glycerol Liquid 56-81-5 >240 >480 >480 6 0.03 0.01 Glycol alcohol Liquid 107-21-1 imm imm imm 6.6 0.002 Hydrochloric acid (16%) Liquid 7647-01-0 imm imm imm na 0.05 Hydrochloric acid (16%) Liquid 7647-01-0 imm imm na 0.05 Hydrochloric acid (32%) Liquid 7647-01-0 imm imm imm na 0.05 Hydrochloric acid (32%) Liquid 7647-01-0 imm imm na 0.05 Hydrogen peroxide (10%) Liquid 7722-84-1 >10 >480 6 <0.01 0.01 Hydrogen peroxide (10%) Liquid 7722-84-1 >10 >10 >480 6 <0.01 0.01 Hydrogen peroxide (30%) Liquid 7722-84-1 imm imm imm >0.11 0.04 Hydrogen peroxide (30%) Liquid 7722-84-1 imm imm >0.11 0.04 Ifosfamide (50 mg/ml) Liquid 3778-73-2 imm >240 5 <0.5 0.003 >480 6 Ifosfamide (50 mg/ml) Liquid 3778-73-2 imm imm >240 5 <0.5 0.003 Irinotecan (20 mg/ml) Liquid 100286-90-6 imm >240 >240 5 <0.1 0.0028 Irinotecan (20 mg/ml) Liquid 100286-90-6 >240 >240 5 <0.1 0.0028 Mercuric II chloride (sat) Liquid 7487-94-7 Methotrexate (25 mg/ml, 0.1 N NaOH) Liquid 59-05-2 >240 >240 5 <0.001 0.001 Methotrexate (25 mg/ml, 0.1 N NaOH) Liquid 59-05-2 >240 >240 >240 5 <0.001 0.001 (Actual) Breakthrough time at MDPR [mins] BTAct Normalized breakthrough time at 0.1 μg/cm²/min [mins] BT0.1 Normalized breakthrough time at 1.0 μg/cm²/min [mins] BT1.0 Classification according to EN 14325 EN Steady state permeation rate [μg/cm²/min] SSPR Minimum detectable permeation rate [μg/cm²/min] MDPR Cumulative permeation mass after 480 mins [μg/cm²] CUM480 Time to reach cumulative permeation Time150 mass of 150 μg/cm² [mins] Classification according to ISO 16602 ISO Chemical abstracts service registry number CAS Minute min Larger than > Smaller than < Immediate (< 10 min) imm Not tested nm Saturated solution sat Not Applicable N/A Not attained na General purpose reagent grade GPR grade Based on lowest single value * Actual breakthrough time; normalized breakthrough time is not available 8 Degradation after 5 min DOT5 Degradation after 30 min DOT30 Degradation after 60 min DOT60 Degradation after 240 min DOT240 Normalized breakthrough time at 0.1 μg/cm²/min [mins] acc. ASTM F1383 BT1383

6. Technical_Description_tyvek-500-accessory-typt31swhl0.pdf printed on February 25, 2021 page of 6 9 Permeation Data for Tyvek® 500 Accessory Hazard / Chemical Name Physical State CAS BT Act BT 0.1 BT 1.0 EN SSPR MDPR Cum 480 Time 150 ISO Mitomycin (0.5 mg/ml) Liquid 50-07-7 >240 >240 >240 5 <0.0009 0.0009 Mitomycin (0.5 mg/ml) Liquid 50-07-7 >240 >240 5 <0.0009 0.0009 Nicotine (9 mg/ml) Liquid 54-11-5 >480 >480 >480 6 <0.08 0.08 Nitric acid (10%) Liquid 7697-37-2 >60 >120 >480 6 na 0.05 Nitric acid (10%) Liquid 7697-37-2 >120 >480 6 na 0.05 >477 5 Nitric acid (30%) Liquid 7697-37-2 imm imm imm 4.6 0.001 Nitric acid (30%) Liquid 7697-37-2 imm imm 4.6 0.001 Oxaliplatin (5 mg/ml) Liquid 63121-00-6 imm imm imm na 0.006 Oxaliplatin (5 mg/ml) Liquid 63121-00-6 imm imm na 0.006 Paclitaxel (Hospira) (6 mg/ml, 49.7 % (v/v) Ethanol) Liquid 33069-62-4 >240 >240 5 <0.01 <0.01 Paclitaxel (Hospira) (6 mg/ml, 49.7 % (v/v) Ethanol) Liquid 33069-62-4 >240 >240 >240 5 <0.01 <0.01 Phosphoric acid (50%) Liquid 7664-38-2 >480 >480 6 <0.05 0.05 Phosphoric acid (50%) Liquid 7664-38-2 >480 >480 >480 6 <0.05 0.05 Potassium chromate (sat) Liquid 7789-00-6 >480 >480 6 <0.005 0.005 Potassium chromate (sat) Liquid 7789-00-6 >480 >480 >480 6 <0.005 0.005 Potassium hydroxide (40%) Liquid 1310-58-3 imm imm >30 2 0.7 0.001 Potassium hydroxide (40%) Liquid 1310-58-3 imm >30 2 0.7 0.001 Propane -1,2,3-triol Liquid 56-81-5 >240 >480 >480 6 0.03 0.01 Sodium acetate (sat) Liquid 127-09-3 imm >480 >480 6 <0.1 0.05 Sodium acetate (sat) Liquid 127-09-3 >480 >480 6 <0.1 0.05 >480 6 Sodium chloride (9 g/l) Liquid 7647-14-5 >240 >240 5 <0.02 0.02 Sodium chloride (9 g/l) Liquid 7647-14-5 >240 >240 >240 5 <0.02 0.02 Sodium hydroxide (10%) Liquid 1310-73-2 >240 >480 >480 6 <0.005 0.005 Sodium hydroxide (40%) Liquid 1310-73-2 imm >30 >240 5 <0.005 0.005 Sodium hydroxide (50%) Liquid 1310-73-2 imm >30 >240 6 0.85 0.01 Sodium hydroxide (>95%, solid) Solid 1310-73-2 >480 >480 >480 6 <0.01 0.01 Sodium hypochlorite (10-15 % active chlorine) Liquid 7681-52-9 >240 >480 6 <0.6 0.05 Sodium hypochlorite (10-15 % active chlorine) Liquid 7681-52-9 >240 >240 >480 6 <0.6 0.05 Sodium hypochlorite (5.25-6%) Liquid 7681-52-9 >480 >480 6 <0.025 0.025 Sodium hypochlorite (5.25-6%) Liquid 7681-52-9 >480 >480 >480 6 <0.025 0.025 (Actual) Breakthrough time at MDPR [mins] BTAct Normalized breakthrough time at 0.1 μg/cm²/min [mins] BT0.1 Normalized breakthrough time at 1.0 μg/cm²/min [mins] BT1.0 Classification according to EN 14325 EN Steady state permeation rate [μg/cm²/min] SSPR Minimum detectable permeation rate [μg/cm²/min] MDPR Cumulative permeation mass after 480 mins [μg/cm²] CUM480 Time to reach cumulative permeation Time150 mass of 150 μg/cm² [mins] Classification according to ISO 16602 ISO Chemical abstracts service registry number CAS Minute min Larger than > Smaller than < Immediate (< 10 min) imm Not tested nm Saturated solution sat Not Applicable N/A Not attained na General purpose reagent grade GPR grade Based on lowest single value * Actual breakthrough time; normalized breakthrough time is not available 8 Degradation after 5 min DOT5 Degradation after 30 min DOT30 Degradation after 60 min DOT60 Degradation after 240 min DOT240 Normalized breakthrough time at 0.1 μg/cm²/min [mins] acc. ASTM F1383 BT1383